Tytuł: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:04:31 Próba Dotyku
ciekawy artykuł: http://www.brusselsprout.org/CNC/1P-Probe/ przedstawiony układzik działa tak: (http://markcomp77.p9.pl/img/sonda-3d-01.jpg) można go nieznacznie uprościć przy połączeniu z optobobem (http://markcomp77.p9.pl/img/sonda-3d-03.jpg) układ mechaniczny sondy działa przy stykach normalnie zamkniętych... kolizja to otwarcie obwodu dawne wątki na ten temat: http://www.cnc.info.pl/topics13/touch-probe-i-turbocnc-vt92.htm?highlight=touch+probe http://www.cnc.info.pl/topics30/praba-dotyku-wykrywanie-siy-nacisku-na-mater-vt648.htm?highlight=touch+probe http://www.cnc.info.pl/topics13/touch-probe-czujnik-przedmiotu-schemat-vt2854.htm?highlight=touch+probe Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:20:15 http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Touch_Probe
Cytuj Touch Probe Information You can choose any input-mode parallel port pin--10, 11, 12, 13, or 15. connect it in your hal file with a line like Kod: net probe parport.0.pin-10-in => motion.probe-input If the signal is inverted (starts at 5V when probe is not in contact, goes to 0V when the probe makes contact), then use the inverted version of the pin: Kod: net probe parport.0.pin-10-in-not => motion.probe-input Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:21:47 http://www.vinland.com/touch-probe.html
(http://www.vinland.com/Images/20080823_140825_w.jpg) Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:23:14 http://www.touch-probe.com/kinematic-resistive-probes/11/
(http://www.touch-probe.com/wp-content/uploads/2011/04/How-the-Kinematic-Resistive-Probe-works1.png) Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:27:07 http://homemetalshopclub.org/projects/touch_probe/touch_probe.html
Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:28:20 http://tom-itx.dyndns.org:81/~webpage/emc/probe_index.php
(http://tom-itx.dyndns.org:81/~webpage/emc/small_probe8_small.jpg) Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:29:24 (http://www.cravingboost.com/machining/images/mill-tools/touch-probe/DSC08919sm.jpg)
http://www.cravingboost.com/machining/x2mill.htm (http://www.cravingboost.com/machining/images/mill-tools/touch-probe/hood-probe02.JPG) Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:32:10 (http://www.mycncuk.com/forums/attachments/probing-digitizing-scaning-webcams/4471d1315263789-touch-probe-ian-005.jpg)
http://www.mycncuk.com/forums/probing-digitizing-scaning-webcams/3739-touch-probe-3.html Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:43:36 Gary's DIY CNC Touch Probe
http://gtocs.blogspot.com/2012/04/garys-diy-cnc-touch-probe.html (http://2.bp.blogspot.com/-uAC3Wh6xT-Q/T4C3UfVUUAI/AAAAAAAAAE4/59j3ddacjh8/s320/insideview.JPG) Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:47:41 Who want to make a touch probe?
http://www.cnczone.com/forums/digitizing_laser_digitizing/28308-want_make_touch_probe.html Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:55:21 Kod: ( Rectangular Probing ) ( ) ( This program repeatedly probes in a regular XY grid and writes the ) ( probed location to the file 'probe-results.txt' in the same directory ) ( as the .ini file ) (Configuration section) G20 (Inches) F4 (probe speed) #1=0 (X start) #2=.25 (X increment) #3=13 (X count) #4=0 #5=.25 #6=5 (Y count) #7=.1 (Z safety) #8=-.5 (Z probe) (End configuration section) (PROBEOPEN probe-results.txt) #9=0 #10=0 G0Z#7 O1 while [#9 lt #6] #10=0 G0 Y[#4+#5*#9] O2 while [#10 lt #3] O3 if [[#9/2] - fix[#9/2] eq 0] G0X[#1+#2*#10] O3 else G0X[#1+#2*[#3-#10-1]] O3 endif G38.2Z#8 G0Z#7 #10=[#10+1] O2 endwhile #9=[#9+1] O1 endwhile (PROBECLOSE) G0Z#7 G0X#1Y#4 M2 Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:56:06 Kod: ( Rectangular Probing ) ( ) ( This program repeatedly probes in a regular XY grid and writes the ) ( probed location to the file 'probe-results.ngc' in the same directory ) ( as the .ini file ) ( This program is adapted to our Touch Probe with a Normally Closed Contact) (Configuration section) G21 (Millimeter) F300.0 (Probe Speed) #1=1 (X start) #2=1 (X increment) #3=135 (X count) #4=1 (Y start) #5=1 (Y increment) #6=2 (Y count) #7=0 (Z safety) #8=-40.0 (Z probe) (End configuration section) (LOGOPEN,probe-results.ngc) #9=0 #10=0 G0Z#7 O1 while [#9 lt #6] #10=0 G0 Y[#4+#5*#9] O2 while [#10 lt #3] O3 if [[#9/2] - fix[#9/2] eq 0] #11=[#1+#2*#10] O3 else #11=[#1+#2*[#3-#10-1]] O3 endif (#11 is X target) #5070=1 O4 while [#5070 NE 0] G38.3 z#7 G38.5 x#11 O4 endwhile G38.5Z#8 (LOG,G1 X#5061 Y#5062 Z#5063) #10=[#10+1] O2 endwhile G0Z#7 #9=[#9+1] O1 endwhile (LOGCLOSE) G0Z#7 G0X#1Y#4 M2 Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:56:50 Kod: ( Rectangular Probing Probe-on-Steroids.ngc ) ( ) ( This program repeatedly probes in a regular XY grid and writes the ) ( probed location to the file 'probe-results.ngc' in the same directory ) ( as the .ini file ) (Revision from the smartprobe.ngc on 13/05/2013. ) ( This program is adapted to our Touch Probe with a Normally Closed Contact) (Added Code for the Norte VS-2000 "G91 G01 Z0.2 & G91" ) (----------------------------------------------------" ) (To obtain it's displacement of, in this case 1mm = #11, the probe ) (builds up the X and Z while moving between G38.3Z and G38.5X until X ) (becomes 1mm. ) (Due to our probe accuracy this resulted in a increased vibration. ) (Since our Machine is a big iron, with a milling head of 3.000kg, ) (we avoided these vibrations by adding this code. ) (It will probably require a different amount of Z on a smaller machine. ) (Added code to obtain a Z- Cruising Line ) (--------------------------------------- ) ( #13= ROUND[#5063] ) ( O6 if [#13 LE #12] ) ( G0 Z#12 ) ( O6 else ) ( G38.5Z#8 ) (This avoids mechanically measuring every time the Z- flat plane by ) (inserting a Z-boundry 1 to 2mm in the air above the real Z- depth. ) (This increases the touch probe speed considerally. ) (Configuration section) G21 (Millimeter) F300.0 (Probe Speed) #1=1 (X start) #2=1 (X increment) #3=135 (X count) #4=1 (Y start) #5=1 (Y increment) #6=5 (Y count) #7=0 (Z safety up) #8=-40.0 (Z probe maximum depth) #12=-34.0 (Z probe down cruising height) #5063=0 (End configuration section) (LOGOPEN,probe-results.ngc) #9=0 #10=0 G0Z#7 G0X#1 Y#4 O1 while [#9 lt #6] #10=0 G0 Y[#4+#5*#9] O2 while [#10 lt #3] O3 if [[#9/2] - fix[#9/2] eq 0] #11=[#1+#2*#10] O3 else #11=[#1+#2*[#3-#10-1]] O3 endif (#11 is X target) #5070=1 O4 while [#5070 NE 0] G38.3 Z#7 G91 G01 Z0.2 (Lines added to the SmartProbe.ngc) G90 (Lines added to the SmartProbe.ngc) G38.5 X#11 O6 endif O4 endwhile #13= ROUND[#5063] O6 if [#13 LE #12] G0 Z#12 O6 else G38.5Z#8 O6 endif (LOG,G1 X#5061 Y#5062 Z#5063) #10=[#10+1] O2 endwhile G0Z#7 #9=[#9+1] O1 endwhile (LOGCLOSE) G0Z#7 G0X#1Y#4 M2 Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:58:45 skanowanie
Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 02:59:34 powyższe jest z LinuxCNC Touch Probe
http://www.vdwalle.com/Norte/ Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 03:00:11 EMC2: Ugliest Tool Length Probe Station… Ever
http://www.vdwalle.com/Norte/EMC2%20%20Ugliest%20Tool%20Length%20Probe%20Station.htm Tytuł: Odp: Próba Dotyku Wiadomość wysłana przez: markcomp Październik 27, 2013, 03:00:27 Improved Tool Length Probe Switch
http://www.vdwalle.com/Norte/Improved%20Tool%20Length%20Probe%20Switch.htm |